gas oil boiler manufacturer in south dumdum
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
292 Chapter 14 Stack—an opening at the top of the boiler that is used to remove flue gas, p. 297. Steam drum—the top drum of a boiler where all of the generated steam is collected before entering the distribution system, p. 293. Steam trap—a device used to remove condensate or liquid from steam systems, p. 294. Superheated steam—steam that has been heated to a very …Get Price
Water in the steam accumulator is steam that has condensed and is therefore clean and pure, with a typical TDS level of 20 - 100 ppm (compared with a shell boiler TDS of seldom less than 2 000 ppm) which promotes a clean and comparatively stable water surface.Get Price
Steam condensing system consists of the following: (a) Condenser (b) Cooling water (c) Cooling tower (d) Hot well (e) Condenser cooling water pump (f) Condensate air extraction pump (g) Air extraction pump (h) Boiler feed pump (i) Make up water pump. 3.1.2 Steam production: Boiler is an apparatus to produce steam.Get Price
(note: pump in front of flywheel to recycle condensed exhaust steam) Typically, the exhaust steam is condensed and pumped back into the boiler to increase efficiency. A small pump on the engine pumps the condensed water into the boiler for a closed loop system. Do-It-Yourself Plans for . this 2 Cylinder Engine are Available below.Get Price
The remaining steam continues to expand to 6 kPa. Steam is then condensed at constant pressure and pumped to the boiler pressure of 8 MPa. Steam leaves the process heater as a saturated liquid at 500 kPa. The mass flow rate of steam through the boiler is 20 kg/s.Determine (a) the rate of process heat supply and (b) the net power developed.Get Price
8 mission factors for System #1 are based on boiler input < 100 MMBtu/hr. Emission E factors for Systems #2 and #3 are based on boiler input > 100 MMBtu/hr. 9 ystem #1 is relatively small and would typically not be integrated with a coal fired S boiler. Emissions for System #1 are only shown for natural gas boiler fuel.Get Price
Pressure gauges are connected to the steam space of the boiler and usually have a ring type siphon tube which fills with condensed steam and protects the dial mechanism from high temperatures. Pressure gauges may be fitted to other pressure containers such as blowdown vessels, and will usually have smaller dials as shown in Figure 3.7.9.Get Price
(note: pump in front of flywheel to recycle condensed exhaust steam) Typically, the exhaust steam is condensed and pumped back into the boiler to increase efficiency. A small pump on the engine pumps the condensed water into the boiler for a closed loop system. Do-It-Yourself Plans for . this 2 Cylinder Engine are Available below.Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
